Hello Carmine,
Meriton Networks intends to use LMP as a fault localization mechanism in
a network of
our
transparent optical switches, currently in the pre-production phase.
I've done some discrete event simulation work to characterize the performance
of an IP
network in support LMP management signals, and the resulting signalling
messages needed
to initiate protection/restoration, and based on the results, have not seen
any need to change
our design direction.
I've also written and submitted an IETF draft
dealing with the importance of control network performance, particularly
when extended across
multiple
networks, and would appreciate any comments you might have.
Regards,
George R. Young
Meriton Networks Inc.
329 March Rd., Kanata, ON, Canada, K2K 2E1
phone: +1 613-270-9279 Ext 287
fax: +1 613-270-9268
Jonathan,
Forgot to mention, that the performance aspects of carrying OAM type signals
over an IP based control channel in LMP-WDM would have to be analyzed.
It is possible that the IP Control Channel will not provide fast enough
transfer to actually suppress downstream alarms, however that needs to
be analyzed as part of LMP-WDM.
Thanks
Carmine
Carmine Daloia wrote:
3BFBA9CC.1060609@lucent.com" type="cite">Jonathan,
The LMP-WDM document specifies the signaling between the Cross-connect
and OLS, assuming they are from different vendors. If they are from
different vendors, then a standard interface is needed to exchange some
information. One type of information that would need to be exchanged
is some OAM signals. Maarten described some of these signals in his
VBI document. However, I don't see why OAM signals would have to be
exchanged directly between the cross-connects themselves via LMP.
Let's look at the following network.
OXC1 --- OLSA --- OXC2 --- OLSB --- OXC3 --- OLSC --- OXC4
Note that the OLS consists of DWDM Mux/Dmux Terminals and Optical Amplifiers.
Let's assume a failure on OLSA. OLSA via overhead within an OSC suppresses
alarms within OLSA. OAM messages (e.g., Optical Channel FDI) could be
carried over the LMP-WDM control channel to OXC2. OXC2 will have to
forward the FDI signals downstream over the LMP-WDM control channel
to OLSB. OLSB will then forward these FDI signals over its OSC and then
over the LMP-WDM control channel to OXC3..... etc...
Note that OXC2 does not need to directly forward these FDI signals to
OXC3. So it is possible, that in LMP-WDM, we may need to define messages
corresponding to FDI signals to suppress downstream alarms, however
we don't need to define such messages in LMP.
Thanks
Carmine
Jonathan Lang wrote:
C12BBE1C7A8F7344808CD8C2A345DFB8455B10@pulsar.chromisys.com" type="cite">
Carmine,
Please see inline.
Thanks,
Jonathan
-----Original Message-----
From: Carmine Daloia [mailto:daloia@lucent.com]
Sent: Monday, November 19, 2001 6:44 AM
To: ccamp@ops.ietf.org
Cc: tsg15q11@itu.int; t1x15@t1.org
Subject: LMP: Suppression of Downstream Alarms...
Hi all,
As I read through Section 6 "Fault Management", one issue that it seems
to be addressing is "Suppression of Downstream Alarms".
In section 6.2, it states that "If data links fail between two PXCs, the
power monitoring system in all of the downstream nodes may detect LOL
and indicate a failure. To avoid multiple alarms stemming from the same
failure, LMP provides a failure notification through the
Cha
nn
elStatus
message...".
I agree that the suppression of downstream alarms is an important issue.
great!
If we look at standard networks (both SONET/SDH and OTN), this
capability is already provided by the overhead in SDH/SONET and G.709
OTN. G.709 OTN handles suppression of alarms in both all-optical
networks as well as opaque networks. I don't think we need to burden the
control plane with such functions when the transport plane handles this
in standard networks. In fact the transport plane handles suppression of
alarms on all equipment in the network (not just cross-connects).
If we look at a pre-OTN ("non-standard") scenario consisting of
Cross-connects, Optical Line Systems, and Optical Amplifiers supporting
a DWDM networked solution, we can analyze two scenarios. One scenario is
an opaque network (e.g., the OLS supports 3R). In this scenario, the
downstream Cross-connects would not detect LOL upon faults occurring
upstream. The 3R points on the OLS Line Systems would insert some type
of signal
dow
ns
tream. Therefore the mechanism described in Section 6.2
does not apply. Another scenario is an all-optical pre-OTN network. Note
that other equipment besides Cross-connects (e.g., Optical Amplifiers)
in an all-optical network may alarm due to upstream faults. These alarms
also need to be suppressed. LMP seems to only address the suppression of
downstream alarms on cross-connects without taking into consideration
the network that sits between the cross-connects. Is LMP also expected
to have to be processed on Optical Amplifiers? This seems to be
undesirable, especially given all the various applications that seem to
be included into the LMP protocol that would not have anything to do
with Optical Amplifieris.
For interaction between cross-connects and Line Systems, please see OLI
Requirements document
(http://search.ietf.org/internet-drafts/draft-many-oli-reqts-00.txt) and
corresponding LMP-WDM protocol document (new version to be uploaded
tomorrow, but old version can be found at
http://search.ietf.org/internet-drafts/draft-fredette-lmp-wdm-02.txt).
Any other views?
Carmine