Between you guys and me, if I were you I'd exercise some judgement. Just one person's opinion. Dave On Wed, Jul 16, 2008 at 02:23:29PM -0700, Templin, Fred L wrote: > Luigi, > > SEAL is right now implemented as a Linux kernel protocol module, and > used to support tunnel-mode and transport-mode applications. It sounds > like what you need is an application-mode instantiation of SEAL, where > the layering would be something like: > > Inner-IP/LISP-SEAL/UDP/Outer-IP > > In that case, to do it at the application layer we would simply need to > pull the 'seal.c' code up into your application and implement some kind > of packet filter that could capture IPv4 first-fragments ICMPv4 "Fragment > Needed" messages at the application layer. That shouldn't be too hard, I > don't think? > > I'll desist now since this is vectoring off into discussion that should go > to the other lists. But, I just wanted to have this application-layer > implementation option for SEAL out on the table since it isn't well > documented in the current spec. > > Fred > fred.l.templin@boeing.com > > > ________________________________ > > From: Luigi Iannone [mailto:Luigi.Iannone@uclouvain.be] > Sent: Wednesday, July 16, 2008 1:56 PM > To: Templin, Fred L > Cc: Olivier.Bonaventure@uclouvain.be; rrg; Sébastien Barré > Subject: Re: [RRG] Publicly available LISP and shim6 implementations > > > Hi Fred, > > in the new openlisp report we cited seal (section 6.8.2) > > I do not know yet the details of your implementation, but if it runs in the user space, thanks to OpenLISP's mapping sockets, to set MTU towards specific RLOCs is pretty easy. > > Cheers > > Luigi > > Le 16-juil.-08 à 22:48, Templin, Fred L a écrit : > > > Oliver et al, > > Integrating LISP with SEAL is a possible next step of interest. > If you would like to try putting your implementation together > with SEAL, let me know: > > http://osprey67.com/seal > > (IMHO, in the future our LISP should be SEALed.) > > Fred > fred.l.templin@boeing.com > > > -----Original Message----- > From: Olivier Bonaventure [mailto:Olivier.Bonaventure@uclouvain.be] > Sent: Wednesday, July 16, 2008 12:35 PM > To: rrg > Cc: Luigi Iannone; Sébastien Barré > Subject: [RRG] Publicly available LISP and shim6 implementations > > Hello, > > To allow researchers to experiment with some of the mechanisms > that are > being extensively discussed on the RRG mailing lists, we are happy to > announce the public release of two implementations : > > - OpenLISP is the first publicly available implementation of > the Locator > Identifier Separation Protocol (LISP) that has been extensively > discussed within the RRG. OpenLISP runs on the FreeBSD kernel and has > been written by Luigi Iannone. > > - LinShim6 is the first implementation of the shim6 IPv6 host-based > multihoming solution developped within the IETF shim6 working group. > LinShim6 runs on the Linux kernel and has been written by > Sebastien Barré. > > You can find additional details (implementation reports, source code, > papers, ...) about these two implementations from our webpage : > > http://inl.info.ucl.ac.be > > > Best regards, > > > Olivier Bonaventure > > PS: Discussion about LISP/shim6 should be sent on the > lisp/shim6 mailing > lists and not on the RRG mailing list > > > -- > to unsubscribe send a message to rrg-request@psg.com with the > word 'unsubscribe' in a single line as the message text body. > archive: <http://psg.com/lists/rrg/> & ftp://psg.com/pub/lists/rrg > > > > > Luigi Iannone > > > luigi.iannone@uclouvain.be > > > >
Attachment:
signature.asc
Description: Digital signature